Author Topic: How to Fix Top Box Lid Stays  (Read 5709 times)

Offline Snigdog

  • Newbie
  • *
  • Posts: 28
  • Thanked: 7 times
  • ST Lurker
How to Fix Top Box Lid Stays
« on: March 06, 2015, 07:37:51 PM »
I don't know how many have had problems with the string stays that hold the top box in the open position........I certainly have.
The string ones that were on the bike wore out/broke and I tried various things to replace them, twine, electrical wire etc. none of which worked particularly well.
I found it hard to judge to the correct length on both sides and then tie off around the little bobbin thingies.

Then I tried cable ties (see picture). They have been brilliant, easy to install and what's more don't get caught between the two halves.
Get a largish cable tie, sit the lid about where you want it and mark the positions of the bobbins. Cut a lengthwise slit in the tie on the mark at each end and then trim the tie to an appropriate overall length.
Fit by pushing the tie where it is slit over the bobbins...you may have to lengthen the slit a little to get it over.
Voila...fixed
sD



Red '06 ST1300
 
The following users thanked this post: Wombat, Bloodman, ruSTynutz

Offline Abe

  • Legendary "1000 Club" Member
  • *****
  • Posts: 1797
  • Thanked: 178 times
  • 4D Gang Member
Re: How to Fix Top Box Lid Stays
« Reply #1 on: March 06, 2015, 07:59:56 PM »
Nice work there Snigdog 

Cheap and replaceable, most of all, it works  :thumbs
At my age " getting lucky" is remembering what I came in the room for ;)

:wht13      Cheers Dave
Member of the 4 D Gang
 

Offline tj189

  • Supreme "2000" Club Member
  • *****
  • Posts: 2131
  • Thanked: 150 times
  • Brisbane
Re: How to Fix Top Box Lid Stays
« Reply #2 on: March 06, 2015, 09:49:57 PM »
Clever  :thumbs thanks for posting it up
IBA #38035
FarRider #189
Ulysses #42456
 

Offline Gadget

  • UNBELIEVABLE "5000 Posts" Member
  • ****
  • Posts: 5564
  • Thanked: 2098 times
  • Just Ridin'
Re: How to Fix Top Box Lid Stays
« Reply #3 on: March 07, 2015, 07:05:57 AM »
:thumbs
Cheers,
Gary
_________________________________________________________________________________________________________
Then  :blu13 Now :Spyder
Life's too short to be miserable, so enjoy it! :)
OzSTOC #257
FarRider #810
IBA #59140

Mob: 04 2448 3555
 

Offline Aussieboy

  • Jr. Member
  • **
  • Posts: 67
  • STeve
Re: How to Fix Top Box Lid Stays
« Reply #4 on: March 07, 2015, 09:05:07 AM »
Great idea thanks for posting. I got a few sets of the originals under warranty. My fix was to glue the ends where they are spliced with super glue and that has seen the last set work for 4 years - worth a try if your originals haven't pulled apart yet.
Steve
2010 ST1300
Ulysses 61988
It's not difficult it's just unfamiliar
 

Offline A2Z

  • Full Member
  • ***
  • Posts: 229
  • Thanked: 45 times
  • Horsley, NSW
Re: How to Fix Top Box Lid Stays
« Reply #5 on: June 02, 2016, 05:54:20 PM »
Brilliant. Just the fix I needed.
Red, loud, rowdy, and proud.

I don't want a pickle...I just wanna ride my motorcikle!
 

Offline Sicman

  • RTE Coordinator
  • Supreme "2000" Club Member
  • *
  • Posts: 2983
  • Thanked: 589 times
  • Was here when the lights got turned on :-)
Re: How to Fix Top Box Lid Stays
« Reply #6 on: June 02, 2016, 06:02:38 PM »
 :clap
Cheers
Tony
FarRider 802
NatRally's - 2012, 2013, 2014, 2015, 2016, 2017, 2018, 2019, 202🤬, 2🤬21, 2021/22 Black Dog bit me, 2023
Experience trumps assumption :-)
 

Offline West Aussie Glen

  • old fart
  • Supreme "2000" Club Member
  • *****
  • Posts: 3154
  • Thanked: 839 times
  • Willetton, Perth
Re: How to Fix Top Box Lid Stays
« Reply #7 on: June 02, 2016, 10:14:12 PM »
I just left mine off but you need to make sure the lid is locked when removing the top box from the bike.
Glen
Sold
1948 James 98cc 2 Speed, 1969 Suzuki A100-2
1970 Suzuki T250 Hustler, Honda CL100
Yamaha RD250C, 1985 Kawasaki GPZ250
BMW K75S, 78 Yamaha XS11
Yamaha Royal Star Tour Deluxe, 88 GL1500
99 SE GL1500
In the shed
85 Kawasaki LTD250
88 GL1500 Outfit
08 ST1300
2013 GL1800
2013 GL1800 Outfit
 

Offline BigTed

  • Was: 2010 ST1300A (Black). Now: 2021 BMW r1250rt
  • Legendary Member
  • *****
  • Posts: 741
  • Thanked: 122 times
  • Perth, WA.
    • The Nook
Re: How to Fix Top Box Lid Stays
« Reply #8 on: June 03, 2016, 09:59:45 AM »
I'm sure I got this idea from OzSToc, possibly during a meet if not on the site...

Pop into a BCF and grab a bag of fishing wire traces. They cost a few bucks and last forever. You can buy them with just loops at each end, or with swivels that can be removed with write cutters.
I think mine were 13cm in length.

https://www.google.com.au/search?q=fishing+trace+wire&client=ms-android-google&biw=412&bih=619&prmd=isvn&source=lnms&tbm=isch&sa=X&ved=0ahUKEwivye-CrorNAhUHopQKHTggAN4Q_AUIBigB#imgrc=MIaD4TGBAJqDfM%3A

Sent from my Nexus 6P using Tapatalk

Rob (in Who's Who)
STOC# 8422

"And yet it moves." - Galileo.
 

Offline A2Z

  • Full Member
  • ***
  • Posts: 229
  • Thanked: 45 times
  • Horsley, NSW
Re: How to Fix Top Box Lid Stays
« Reply #9 on: June 03, 2016, 10:18:03 AM »
Another problem I have with this is that the threads on the box where you screw it into are stripped. Any fix for this? 
Red, loud, rowdy, and proud.

I don't want a pickle...I just wanna ride my motorcikle!
 

Offline ST2UP

  • The Pockey Poker ;)
  • Administrator
  • UNBELIEVABLE "5000 Posts" Member
  • *****
  • Posts: 5596
  • Thanked: 1312 times
  • Guyra - NSW
Re: How to Fix Top Box Lid Stays
« Reply #10 on: June 03, 2016, 11:42:07 AM »
Another problem I have with this is that the threads on the box where you screw it into are stripped. Any fix for this?

Larger diameter screw (BUT NOT LONGER).....

Fill screw hole with supa glue or similar and re-drill after its set  :think1


 :beer
Chris    



IBA #64116   FarRider #660   Ulysses #56339

st2up@ozstoc.com

Mbl: 0428792425

Sighted it....Wanted it...Chucked a fit...GOT IT !!!!
 

Offline Biggles

  • NatRally 2018 - Mackay
  • "Top Dog" 10000 club
  • *
  • Posts: 14026
  • Thanked: 2474 times
  • Bridgeman Downs, Brisbane
Re: How to Fix Top Box Lid Stays
« Reply #11 on: June 03, 2016, 12:16:02 PM »

Larger diameter screw (BUT NOT LONGER).....

Fill screw hole with supa glue or similar and re-drill after its set  :think1


Not superglue.  It basically has no gap-filling capacity.  JB-Weld or other hard-setting epoxy is the go.  I like Kneadit- behaves like putty and sets like rock and can be drilled and tapped.  Comes in white for wood or black for metal.
For the modern man who lives in the city, riding a bike might be one of the only ways to escape the humdrum monotony. To take off and ride. To be both at one with nature and one with the bike. To feel masculine. Adam Piggott

OzSTOC #16  STOC #6135  FarR #509  IBA #54927
 

Online ruSTynutz

  • NR2024 Rally Team
  • Supreme "2000" Club Member
  • *
  • Posts: 4431
  • Thanked: 2791 times
    • "Destined to Drive" Driving School
Re: How to Fix Top Box Lid Stays
« Reply #12 on: November 25, 2019, 04:31:22 PM »
I decided to make some "stays" for my top box as the originals were missing when I bought my ST...

I ended up buying a length of 3.6mm bead chain. Luckily it came with 4 loop ends which worked out perfect!

The chain is rated at 6kg working load so I figured that should be fine considering the top box lid doesn't weigh much.
I then got some 4mm flexible tubing to slide over the chain so the balls don't catch on anything and to also "encourage" the stays to fold inside the top box when closing...

I just used a few washers & a nut to "pack" the mounts so the screws didn't pop through where they shouldn't.

It all works perfectly!  :thumbsup

Now, if I can source some replacement "loop ends" I just might have to knock out a few more as I have a stack of chain & tubing left over... :whistle

     

 



        2005 Honda ST1300A
 
The following users thanked this post: richo, Bloodman, CallMeSteve

Offline Biggles

  • NatRally 2018 - Mackay
  • "Top Dog" 10000 club
  • *
  • Posts: 14026
  • Thanked: 2474 times
  • Bridgeman Downs, Brisbane
Re: How to Fix Top Box Lid Stays
« Reply #13 on: November 25, 2019, 11:18:29 PM »
That's a very elegant fix.  I'm sure there would be plenty of people on the forum who would gladly pay bux for a pair if you can source "loop ends".
The joiners they sell for the chains that operate blinds may do the trick.  You could check suppliers because I know they sell the bits apart from the blinds.
For the modern man who lives in the city, riding a bike might be one of the only ways to escape the humdrum monotony. To take off and ride. To be both at one with nature and one with the bike. To feel masculine. Adam Piggott

OzSTOC #16  STOC #6135  FarR #509  IBA #54927
 
The following users thanked this post: ruSTynutz

Online ruSTynutz

  • NR2024 Rally Team
  • Supreme "2000" Club Member
  • *
  • Posts: 4431
  • Thanked: 2791 times
    • "Destined to Drive" Driving School
Re: How to Fix Top Box Lid Stays
« Reply #14 on: November 26, 2019, 08:51:25 AM »
Thanks Biggles!  :thumbs
I managed to source some off ebay last night so I ended up ordering 4 packs which will be enough to make up four sets...


        2005 Honda ST1300A
 

Online ruSTynutz

  • NR2024 Rally Team
  • Supreme "2000" Club Member
  • *
  • Posts: 4431
  • Thanked: 2791 times
    • "Destined to Drive" Driving School
Re: How to Fix Top Box Lid Stays
« Reply #15 on: December 05, 2020, 04:30:19 PM »
Well, I decided to replace my "stays" as, while the bead chain was easily strong enough, the "loop ends" weren't...
Twice now I've had a loop end spring apart just enough to let the ball chain rip out.
This has happened when there's been a strong wind pulling on the lid while open.

Anyhow, I decided to come up with a much stronger "fix"...  :thumb

I ended up using some 2mm stainless steel cable wrapped around the original red restraint mounts and then "fastened" with a 2mm Stainless Steel Swage.
As with my previous "ball" restraints, I ran the cable through some flexible tubing, mainly so the cable wouldn't rub (& possibly damage) the edge of the top box lid when open.




        2005 Honda ST1300A
 
The following users thanked this post: Shiney

Offline Gadget

  • UNBELIEVABLE "5000 Posts" Member
  • ****
  • Posts: 5564
  • Thanked: 2098 times
  • Just Ridin'
Re: How to Fix Top Box Lid Stays
« Reply #16 on: December 05, 2020, 06:50:55 PM »
:thumbs

Sent from my SM-N986B using Tapatalk

Cheers,
Gary
_________________________________________________________________________________________________________
Then  :blu13 Now :Spyder
Life's too short to be miserable, so enjoy it! :)
OzSTOC #257
FarRider #810
IBA #59140

Mob: 04 2448 3555
 
The following users thanked this post: ruSTynutz

Offline West Aussie Glen

  • old fart
  • Supreme "2000" Club Member
  • *****
  • Posts: 3154
  • Thanked: 839 times
  • Willetton, Perth
Re: How to Fix Top Box Lid Stays
« Reply #17 on: December 05, 2020, 10:10:41 PM »
I have just left mine off. Trick is not to pick it up by the handle when off the bike and you haven't locked the lid closed.
Glen
Sold
1948 James 98cc 2 Speed, 1969 Suzuki A100-2
1970 Suzuki T250 Hustler, Honda CL100
Yamaha RD250C, 1985 Kawasaki GPZ250
BMW K75S, 78 Yamaha XS11
Yamaha Royal Star Tour Deluxe, 88 GL1500
99 SE GL1500
In the shed
85 Kawasaki LTD250
88 GL1500 Outfit
08 ST1300
2013 GL1800
2013 GL1800 Outfit
 
The following users thanked this post: ruSTynutz

Offline richo

  • Richo
  • Legendary Member
  • *****
  • Posts: 957
  • Thanked: 394 times
  • ST 2009
Re: How to Fix Top Box Lid Stays
« Reply #18 on: December 06, 2020, 07:00:27 AM »
 :thumbsup :thumbsup.  Looks good. I will have to borrow this one
Richo
 
The following users thanked this post: ruSTynutz

Online ruSTynutz

  • NR2024 Rally Team
  • Supreme "2000" Club Member
  • *
  • Posts: 4431
  • Thanked: 2791 times
    • "Destined to Drive" Driving School
Re: How to Fix Top Box Lid Stays
« Reply #19 on: December 06, 2020, 09:57:46 AM »
Go for it, Richo... :thumbs




        2005 Honda ST1300A