Author Topic: LED Strobes for the ST1100 (or 1300) (Read 12612 times)

Brock · « **on:** April 30, 2015, 07:55:53 PM »

My Narva 85203A Amber LEDs have finally arrived from Redline (Half the price of the Auto stores). Brackets have been manufactured, mounting holes drilled and tapped. Now the wiring to do. Photos later. there will be four 3LED light heads to the rear and two on the front. Currently programmed into two groups,. so the flashes will alternate.

I may at a later date fit another pair to each side. A short movie of the finished job will be posted.

Biggles · « **Reply #1 on:** April 30, 2015, 08:41:51 PM »

Quote from: Brock on April 30, 2015, 07:55:53 PM

I may at a later date fit another pair to each side. A short movie of the finished job will be posted.

And a circuit diagram, or will that be subject to patent rights?

Brock · « **Reply #2 on:** April 30, 2015, 10:04:12 PM »

And a circuit diagram as it applies to this LED set. The lights are able to be dimmed at night, and will be able to have the flash pattern changed as well.

tj189 · « **Reply #3 on:** May 01, 2015, 07:00:10 AM »

Biggles · « **Reply #4 on:** May 01, 2015, 09:37:02 AM »

Quote from: Brock on April 30, 2015, 10:04:12 PM

And a circuit diagram as it applies to this LED set. The lights are able to be dimmed at night, and will be able to have the flash pattern changed as well.

With a parts list...

Brock · « **Reply #5 on:** May 01, 2015, 10:37:41 AM »

and a sock....

Biggles · « **Reply #6 on:** May 01, 2015, 02:21:53 PM »

Quote from: Brock on May 01, 2015, 10:37:41 AM

and a sock....

Nup. Got socks. In pairs!
It's a parts list I'd be looking for.

Brock · « **Reply #7 on:** May 03, 2015, 02:32:19 PM »

This is one of the six Narva 3LED modules.

The parts to make up the system

Brock · « **Reply #8 on:** May 03, 2015, 02:36:33 PM »

The rear LED Bar

The front LED Units

Front modules fitted

Rear Modules fitted.

Brock · « **Reply #9 on:** May 03, 2015, 02:40:30 PM »

The interconnecting loom, still under construction, and the site supervisor.

Brock · « **Reply #10 on:** May 03, 2015, 02:42:10 PM »

Still lots of work to do lots of wiring to be connected and plugs fitted.

Brock · « **Reply #11 on:** May 04, 2015, 04:56:35 PM »

Here is the circuit as applied to the 1100 police version, the 1300 should be the same.

Circuit removed for now, the is a fault in the main wiring diagram.

Biggles · « **Reply #12 on:** May 04, 2015, 10:02:20 PM »

Very tidy diagram. Well done. Thanks for that.

Brock · « **Reply #13 on:** May 04, 2015, 10:33:10 PM »

It looks easier on paper, its a bugger to make, especially as I am spicing into the loom and heat shrinking every thing and putting plugs on it so broken LEDs can be easily replaced.

Cutting stripping twisting and crimping wire is wrecking my delicate hands and fingers.

I will put up a generic diagram a bit later.

bloodbikes · « **Reply #14 on:** May 06, 2015, 09:29:17 AM »

I used the number 6 momentary switch to change patterns.

Brock · « **Reply #15 on:** May 06, 2015, 02:42:32 PM »

The number 3 will do that, (via relay), 1 will be fore and aft, 2 will be side (if I fit them )

Brock · « **Reply #16 on:** May 06, 2015, 08:55:40 PM »

Circuit removed for now There are some faults in the diagram, more research needed.

bloodbikes · « **Reply #17 on:** May 06, 2015, 10:55:15 PM »

What are you stuck on? You shouldn't need a relay for any of the connections. What circuit have you removed?
Can I help?

bloodbikes · « **Reply #18 on:** May 06, 2015, 11:11:59 PM »

Quote from: Brock on May 04, 2015, 10:33:10 PM

It looks easier on paper, its a bugger to make, especially as I am spicing into the loom and heat shrinking every thing and putting plugs on it so broken LEDs can be easily replaced.

Cutting stripping twisting and crimping wire is wrecking my delicate hands and fingers.

I will put up a generic diagram a bit later.

You have a 5 year warranty on LEDs, I don't think you'll be replacing them anytime soon.

Brock · « **Reply #19 on:** May 07, 2015, 08:31:43 AM »

The relay is to allow the 3 switch to change the flash pattern, as the switch switches an earth(return). to change the pattern requires a 12V+ applied to the sync wire. If I apply an earth, the light will just dim.

The circuit was the wiring diagram, the original I was using had some errors that I need to fix before its republished

Brock · « **Reply #20 on:** May 08, 2015, 10:14:20 PM »

Got the strobes working on the rear, the are visible from quite a wide angle.

Brock · « **Reply #21 on:** May 08, 2015, 10:17:47 PM »

bloodbikes · « **Reply #22 on:** May 08, 2015, 10:21:30 PM »

Looking good Brock, they won't miss you now.

tj189 · « **Reply #23 on:** May 09, 2015, 07:33:52 AM »

They have come up good, well done

Brock · « **Reply #24 on:** May 09, 2015, 10:14:30 PM »

All working now,

Note the prominent red and blue light on the dash ( its the SR10 ) that may be why cars get out of the way in the morning run up the freeway.

News:

Author Topic: LED Strobes for the ST1100 (or 1300) (Read 12612 times)