Author Topic: Steadycam - just for interest  (Read 3631 times)

Offline Rodd

  • Sr. Member
  • ****
  • Posts: 348
  • Thanked: 80 times
  • Maryborough, QLD
Steadycam - just for interest
« on: December 15, 2013, 05:21:54 PM »
If you look around on the internet there are all sorts of instructions on how to film better videos as well as do-it-yourself gadgets.
Just for the fun of it I had a go at making my own steadycam mount. It's based on ones shown on the internet but made using my sons' old scooter parts.



It cost about $15 because the sealed bearings in the scooter wheels were stuffed, so I had to buy new ones. Framework for the centre gimbal, and the white bearing holders where from Bunnings.
 

Offline Marcus

  • Insert amusing quip here...
  • RTE Coordinator
  • Supreme "2000" Club Member
  • *
  • Posts: 3127
  • Thanked: 377 times
  • It says Stringo on my shirt
Re: Steadycam - just for interest
« Reply #1 on: December 15, 2013, 07:16:10 PM »
An actual upside down tripod will do the same thing. I can link the vid if anyone wants it
 

Offline Rodd

  • Sr. Member
  • ****
  • Posts: 348
  • Thanked: 80 times
  • Maryborough, QLD
Re: Steadycam - just for interest
« Reply #2 on: December 15, 2013, 07:17:42 PM »
I've seen the video and have tried that with my tripod, but it's not the same.
 

Offline Marcus

  • Insert amusing quip here...
  • RTE Coordinator
  • Supreme "2000" Club Member
  • *
  • Posts: 3127
  • Thanked: 377 times
  • It says Stringo on my shirt
Re: Steadycam - just for interest
« Reply #3 on: December 15, 2013, 07:53:22 PM »
Post up equipment and part list please... I've been meaning to try this as well
 

Offline Rodd

  • Sr. Member
  • ****
  • Posts: 348
  • Thanked: 80 times
  • Maryborough, QLD
Re: Steadycam - just for interest
« Reply #4 on: December 15, 2013, 08:33:33 PM »
When I first saw the tripod idea I thought that it was a great piece of lateral thinking. It's just a matter of removing the screw from one of the leg slides, moving the leg to vertical while having the tripod horizontal and walking with the tripod swinging below. It's a good cheap way (assuming that you already have a suitable tripod) but I found a few disadvantages with it. You needed to carry a screwdriver to remove the screw on the leg slide (or modify it with another screw and wingnut). You use the other legs to balance the camera by sliding them in or out to suit. The disadvantage for me was that the legs were obtrusive when used in tighter situations (and not so tight as well) by hitting things when you turned. These situations can be where you want to move around between bikes, around crowds, or through workshops. The other disadvantage was that it only works when slung low relying on the length of your arm and the tripods leg along with gravity to take some unwanted movement out. Once you lift it up it loses it's usefulness. Also, if you then needed your tripod you would have to convert it back.. not a big job but the advantages of having gadgets is usually due to the convenience once you have them. Having said that, it can be a useful tool in certain situations.

To build my steadicam I confiscated my sons now unused fold up scooter. I used the steering stem and handlebars, and the rear brake has become the handle.
Unfortunately, the scooters wheel bearings were shot so I went to the local pushbike shop and bought some skateboard/scooter wheel bearings. The bearing caps are 3/4" water pipe end caps. They required a little sanding until the bearings fit snuggly inside. The framework for the gimble is made from cheap galvanised strapping bought from Bunnings.

4x scooter/skateboard sealed wheel bearings - A bit over $2 each. (22mm o/d and 8mm axle hole).
3/4" plastic water pipe end caps - ~ $1.50 each
Galvanised strapping - ~$2 per length.. I bought two lengths.

The bolts for the axles for the bearings are 8mm, but I already have a stack in different types and styles. The mounting bolts for the bearing holders were 6mm, and I had dome nuts here.
I already had a stainless steel angle bracket that has been cut up and used on the ST's Police light bracket camera mounts, and it was used as a camera mount on this steadicam. With the Drift Ghost it gives you up/down and swivel adjust-ability. I made the job easier for myself by simply using some thick dowel to fit into the neck of the steadicam to affix the camera mount to. I drilled and fitted a 1/4" threaded rod into the dowel.

Once built you need to spend some time getting the balance just right. Once done you can mark the positioning for later reference.
The scooters steering stem is adjustable for height to allow it to be folded away. On the steadicam it is used to coarsely adjust the balance between the mounted camera and the bottom arms. I used the scooters locking clamp to attach the handle brackets to, and it is also used to make finer changes to the balance with the camera on the steadicam. The lower arms (previously the scooters hand-grips) are removable for storage, and the slide on the steering stem can be made shorter for storage.

Please refer to the photo as a reference to building and assembly.
 

Offline Rodd

  • Sr. Member
  • ****
  • Posts: 348
  • Thanked: 80 times
  • Maryborough, QLD
Re: Steadycam - just for interest
« Reply #5 on: December 15, 2013, 08:43:16 PM »
I should add that the advantages are that the gimble is virtually friction free for this purpose. The steadicam doesn't require a lot of room to move around. You can raise and lift the camera from a useful low to quite high - handy for the wider angle lens of action cams.
Many of the steadicam designs allow the camera to swivel freely as well. There are advantages and disadvantages to that.
The disadvantages - they need to be balanced fairly well to work properly. If you use a dslr camera with adjustable lens length then the balance would need to be adjusted when the lens is lengthened/shortened. This isn't a problem with action cameras.
 

Offline Marcus

  • Insert amusing quip here...
  • RTE Coordinator
  • Supreme "2000" Club Member
  • *
  • Posts: 3127
  • Thanked: 377 times
  • It says Stringo on my shirt
Re: Steadycam - just for interest
« Reply #6 on: December 16, 2013, 07:08:26 AM »
Brilliant write up Rodd, thanks for sharing
 

Online StinkyPete

  • Defected to a BMW
  • UNBELIEVABLE "5000 Posts" Member
  • ****
  • Posts: 6582
  • Thanked: 3010 times
  • Blackwood, SA
Re: Steadycam - just for interest
« Reply #7 on: December 16, 2013, 07:20:08 AM »
Rodd.   Very inventive indeed.  You're an ideas man.   :clap
IBA #59146   OzLapper 2012 & 2019

BSA M21 600cc single (1948)
Yamaha XS650  (The Black Wobbler)
Yamaha XJR1300 (Rocket Ship)
Honda ST1300 (Beautiful Bike)
BMW R1200RT (Technically Perfect)
Currently Bikeless
 

Offline Rodd

  • Sr. Member
  • ****
  • Posts: 348
  • Thanked: 80 times
  • Maryborough, QLD
Re: Steadycam - just for interest
« Reply #8 on: December 16, 2013, 11:07:04 AM »
Thanks fellas. It's good to be able to use my workshop and some of the 'stuff' that I seem to keep 'because it might be useful'.

 :think1