Author Topic: Gear Lever  (Read 5564 times)

Online Williamson

  • UNBELIEVABLE "5000 Posts" Member
  • ****
  • Posts: 5258
  • Thanked: 2375 times
  • ST Legend
Gear Lever
« on: March 05, 2016, 10:48:50 AM »
The gear lever on my 2011 ST1300 won't ...... lever this is!!

Out for a short ride to Whittlesea this AM to meet some of my / our Ulysses colleagues, and my gear lever stopped levering, the gear shifter stopped shifting - stuck in 3rd gear. 

Limped home, parked in garage, on to centre stand, LH lower fairing off.  Still pretty dark in there (a torch helped), very tight, no room for hands or even a good look, but it seems like the lever system has been disconnected between items 4 and 5 in this diagram.



This from a link provided by Saaz (RIP) for 2003 - 2004 model ST1300's. 

Any clues or advice from others on this matter, eg:
*  Do you think I'm on the right track? 
*  Is some thing broken in there or 4 and 5 just separated
*  Do I keep pulling off side panels for a better look, next one look like the panel that the pillion foot rest is mounted on, this means also removing the tow bar or at least part of it?
*  Am I off-track altogether, sans the tow bar?
*  Do I pack back together and take it to the dealer?
Cheers,  Williamson (AKA Michael)

Motorcycling, the best time you can have with your pants on.
eBiking, the second best time you can have with your pants on
Afterlife, up there for the climate, down there for the company.
If I'd known I was gunna live this long, I woulda looked after myself better
 
The following users thanked this post: Draco (Heartbreak Kid)

Online Brock

  • Tardis Tech
  • UNBELIEVABLE "5000 Posts" Member
  • ****
  • Posts: 8793
  • Thanked: 1763 times
  • White is the fastest
Re: Gear Lever
« Reply #1 on: March 05, 2016, 10:57:04 AM »
The rod ends are known to occasionally get stiff. (item 4) pull them off and give them a good lube (lithium grease should do the trick).

While the rod end is off, try the gear lever for free movement.
Brock
Asian Correspondent
2003 Honda ST1100PY



Ulysses #32829
STOC #8239
OzSToc # ??
Kinross WA
 
The following users thanked this post: Williamson, Draco (Heartbreak Kid)

Online Williamson

  • UNBELIEVABLE "5000 Posts" Member
  • ****
  • Posts: 5258
  • Thanked: 2375 times
  • ST Legend
Re: Gear Lever
« Reply #2 on: March 05, 2016, 11:12:07 AM »
The rod ends are known to occasionally get stiff. (item 4) pull them off and give them a good lube (lithium grease should do the trick).

While the rod end is off, try the gear lever for free movement.


Don't think it's stiff, the outer lever just floats around, floppy like.

Perhaps it was stiff, and little to much effort on my part caused it to come adrift.  Didn't seem stiff before though, although now thinking back there was one very firm "clunk" when selecting 1st gear at an earlier stop.

Looks like I'll have to remove this panel to get a good look.




Cheers,  Williamson (AKA Michael)

Motorcycling, the best time you can have with your pants on.
eBiking, the second best time you can have with your pants on
Afterlife, up there for the climate, down there for the company.
If I'd known I was gunna live this long, I woulda looked after myself better
 
The following users thanked this post: Draco (Heartbreak Kid)

Offline HunterTodd

  • Sr. Member
  • ****
  • Posts: 369
  • Thanked: 36 times
  • HunterTodd
Re: Gear Lever
« Reply #3 on: March 05, 2016, 12:08:19 PM »
The crank has not come of the spline on the shaft where it exits the crankcase. This is on the lower rear right hand side of the engine and you dont need to remove any plastic to see it. If that link is not on the gear lever feels floppy and it obviously will stay in the last gear which was selected.
 
The following users thanked this post: Williamson, Draco (Heartbreak Kid)

Online Williamson

  • UNBELIEVABLE "5000 Posts" Member
  • ****
  • Posts: 5258
  • Thanked: 2375 times
  • ST Legend
Re: Gear Lever
« Reply #4 on: March 05, 2016, 12:12:07 PM »
I have removed the oil filter to get a better view and discovered it's come adrift between 5 and 18.  Bloody damn hell poop, it's awkward in there.
Cheers,  Williamson (AKA Michael)

Motorcycling, the best time you can have with your pants on.
eBiking, the second best time you can have with your pants on
Afterlife, up there for the climate, down there for the company.
If I'd known I was gunna live this long, I woulda looked after myself better
 
The following users thanked this post: Draco (Heartbreak Kid)

Offline Brian

  • Legendary "1000 Club" Member
  • *****
  • Posts: 1674
  • Thanked: 302 times
  • ST Immortal
Re: Gear Lever
« Reply #5 on: March 05, 2016, 12:55:17 PM »
I have removed the oil filter to get a better view and discovered it's come adrift between 5 and 18.  Bloody damn hell poop, it's awkward in there.

Sounds like an easy fix........ Nicely done
I jus wanna ride my bike

09 ST1300 Charcoal Metallic (Grey GhoST)
09 ST1300 Candy Glory Red (Red MiST)
 
The following users thanked this post: Williamson, Draco (Heartbreak Kid)

Online Williamson

  • UNBELIEVABLE "5000 Posts" Member
  • ****
  • Posts: 5258
  • Thanked: 2375 times
  • ST Legend
Re: Gear Lever
« Reply #6 on: March 05, 2016, 01:03:33 PM »
I have removed the oil filter to get a better view and discovered it's come adrift between 5 and 18.  Bloody damn hell poop, it's awkward in there.

Sounds like an easy fix........ Nicely done

I wish, 40 minutes to get the turnbuckle (I think that's the right term) on and tighten two 10mm lock nuts.  Hope the gear lever is in the correct position, can't test it until I start the motor, can't do that until I put on a new oil filter and replace the oil, then I can't access the top lock nut.

Grrrrrrr!!!!!!!
Cheers,  Williamson (AKA Michael)

Motorcycling, the best time you can have with your pants on.
eBiking, the second best time you can have with your pants on
Afterlife, up there for the climate, down there for the company.
If I'd known I was gunna live this long, I woulda looked after myself better
 
The following users thanked this post: Draco (Heartbreak Kid)

Online Williamson

  • UNBELIEVABLE "5000 Posts" Member
  • ****
  • Posts: 5258
  • Thanked: 2375 times
  • ST Legend
Re: Gear Lever
« Reply #7 on: March 06, 2016, 10:49:35 AM »
All back together, test run ....... well okay, gear lever a little higher than I would like, will see how it goes, if I can't get use to it, oil drain, filter 'off', adjust turn buckle, replace oil / filter, might wait until next scheduled change.

Problem was the little lock nuts (13 and 18 in diagram) coming loose, turn buckle came adrift.



I got lock nut 13 very tight, lock nut 18 was very hard to get to and a little more than finger tight.  I figure if 13 is very tight, turn buckle (am I using the correct term for the threaded rod with a clockwise thread one end, and an anti-clockwise thread the other end?) will not rotate and 18 or the thread that screws into 5 will not come loose, and all should be well.

Please, tell me my theory is sound, I'll let you know if it is in practice .......... in due course.
Cheers,  Williamson (AKA Michael)

Motorcycling, the best time you can have with your pants on.
eBiking, the second best time you can have with your pants on
Afterlife, up there for the climate, down there for the company.
If I'd known I was gunna live this long, I woulda looked after myself better
 

Online Brock

  • Tardis Tech
  • UNBELIEVABLE "5000 Posts" Member
  • ****
  • Posts: 8793
  • Thanked: 1763 times
  • White is the fastest
Re: Gear Lever
« Reply #8 on: March 06, 2016, 11:02:12 AM »
Not sure if it can be done, but you may be able to take the whole assembly out and tighten the nuts. Then put it back. The rod ends just press back back on to the ball ends.
Brock
Asian Correspondent
2003 Honda ST1100PY



Ulysses #32829
STOC #8239
OzSToc # ??
Kinross WA
 
The following users thanked this post: Williamson

Online Williamson

  • UNBELIEVABLE "5000 Posts" Member
  • ****
  • Posts: 5258
  • Thanked: 2375 times
  • ST Legend
Re: Gear Lever
« Reply #9 on: March 06, 2016, 11:07:56 AM »
Not sure if it can be done, but you may be able to take the whole assembly out and tighten the nuts. Then put it back. The rod ends just press back back on to the ball ends.

I'll look at that option if I need to.  But I forecast that getting 4 and 5 apart, then back together will be a real problem.  There isn't enough room in there for my hands and fingers (which ain't large compared to some of yuse blokes).
Cheers,  Williamson (AKA Michael)

Motorcycling, the best time you can have with your pants on.
eBiking, the second best time you can have with your pants on
Afterlife, up there for the climate, down there for the company.
If I'd known I was gunna live this long, I woulda looked after myself better
 

Offline alans1100

  • 1999 ST1100A
  • UNBELIEVABLE "5000 Posts" Member
  • ****
  • Posts: 6249
  • Thanked: 1161 times
  • Alan, Peterborough, SA
Re: Gear Lever
« Reply #10 on: March 06, 2016, 01:51:59 PM »
There's some instructions here with adjusting pedal height after fitting a MCL Peg Lowering Kit - not sure if it will help but no harm in looking   http://www.st-owners.com/forums/showthread.php?8940-ST1300-MCL-Peg-Lowering-Kit&highlight=adjust%20shifter
1999 :bl11  2004 :13Candy

FarRider #921- BR15, BR17, CR1

 
The following users thanked this post: Williamson