Author Topic: How to ID an ST1300 ABS  (Read 7057 times)

Offline ST.George

  • ST.George and his ST1300 Red Dragon (Wyvern)
  • Legendary Member
  • *****
  • Posts: 569
  • Thanked: 33 times
  • DIY not DYI(Do Yourself In) "The Gong"Southern NSW
How to ID an ST1300 ABS
« on: December 22, 2014, 11:23:45 AM »
G'day STriders,

After reading thru the posts by BikeBugger recently one of the issues was an ABS light on a supposedly non-ABS bike.

Looking thru my Haynes manual I was unable to find any photos of ABS sensors. Why I am querying this is coz I bought my 2003 STeed a cupla years back, from a Honda mechanic in Qld. The bike was described and sold as non-ABS. However the rego papers said it is a 1300A and a sticker under the seat also states that it is a 1300A. Does the pic below show anything definitive that indicates ABS or not - is that a sensor on the fork?






Also there is no ABS light in my instruments that I have noticed so it's very likely not 2 b ABS.

So I thought if anyone can tell from these pix or has pix that clearly ID an ABS system that would be gr8.
« Last Edit: December 22, 2014, 12:26:58 PM by ST.George »
:beer Cheers :beer Gregory
:rd13   Best Bred is Red   :rd13
"Spock - there's a black hole on the other side of Uranus".
"Illogical Captain".
I think I might be indecisive, I'm not sure, maybe - maybe not.
Yamaha TX500; Yamaha DT360; BMW 650 Boxer; 2003 ST1300 Red Dragon
 

Offline saaz

  • Supreme "2000" Club Member
  • *****
  • Posts: 4542
  • Thanked: 41 times
  • Canberra ACT
Re: How to ID an ST1300 ABS
« Reply #1 on: December 22, 2014, 11:26:53 AM »
I don't know on which side the sensor should be, but there will be an extra ring inside the rotor with lots of perforations (pulser ring) with a sensor that reads wheel rotation. If the other side of the front wheel looks like the right side shown, no ABS.

Just looked in the manual, and the pulser ring is on the right side pictured, so you don't have the A model (ABS)

Other bikes will vary. The FJR1300 for example, has the disk which is part of the ABS hidden under a cover on the left side front so you have to look closer for the ABS sensor.
« Last Edit: December 22, 2014, 11:37:24 AM by saaz »
John
(Ridden on and forever in our hearts)
1996 Honda ST1100P
2014 Triumph Trophy SE
Ozstoc, STOC #7239, Farrider #461 Ulysses #061681, IBA #59143 and some others
 

Offline Gordo

  • Gordo
  • Full Member
  • ***
  • Posts: 113
  • Thanked: 56 times
  • ST Legend
Re: How to ID an ST1300 ABS
« Reply #2 on: December 22, 2014, 12:14:31 PM »
ST. George
If you look at the attached photo of my bike you can see the ring that saaz is referring to for the ABS. I think that the sensor you are referring to is a connection for the bikes linked braking system.

GORDO
FarRider #550
 

Offline Gordo

  • Gordo
  • Full Member
  • ***
  • Posts: 113
  • Thanked: 56 times
  • ST Legend
Re: How to ID an ST1300 ABS
« Reply #3 on: December 22, 2014, 12:15:50 PM »
Try that again with the attachment this time.

GORDO
FarRider #550
 

Offline alans1100

  • 1999 ST1100A
  • UNBELIEVABLE "5000 Posts" Member
  • ****
  • Posts: 6249
  • Thanked: 1161 times
  • Alan, Peterborough, SA
Re: How to ID an ST1300 ABS
« Reply #4 on: December 22, 2014, 02:03:40 PM »
ST. George
If you look at the attached photo of my bike you can see the ring that saaz is referring to for the ABS. I think that the sensor you are referring to is a connection for the bikes linked braking system.

GORDO

You should also have a sensor for the rear wheel with the mount possibly mounted on top of the final drive like they do with the 1100
1999 :bl11  2004 :13Candy

FarRider #921- BR15, BR17, CR1

 

Offline ST.George

  • ST.George and his ST1300 Red Dragon (Wyvern)
  • Legendary Member
  • *****
  • Posts: 569
  • Thanked: 33 times
  • DIY not DYI(Do Yourself In) "The Gong"Southern NSW
Re: How to ID an ST1300 ABS
« Reply #5 on: December 22, 2014, 02:25:47 PM »
Gr8 stuff guys, thnxalot.  :clap :hatwave

Wyvern definitely not ABS and Wyvern says "That's good master coz when I wanna skid - man - I WANNA SKID!". I dunno about u guys, I'm not upset about not being ABS coz I remember on my pushie days as a teen I used to come to a far better controlled stop when traction is lost by steering into the slide and then accelerating when the direction was right. Come to think of it I did do something like that when I had my YammieDT360 dirt/trail. Hence ABS must be absolutely useless on a loose surface - correct?


:beer Cheers :beer Gregory
:rd13   Best Bred is Red   :rd13
"Spock - there's a black hole on the other side of Uranus".
"Illogical Captain".
I think I might be indecisive, I'm not sure, maybe - maybe not.
Yamaha TX500; Yamaha DT360; BMW 650 Boxer; 2003 ST1300 Red Dragon
 

Offline alans1100

  • 1999 ST1100A
  • UNBELIEVABLE "5000 Posts" Member
  • ****
  • Posts: 6249
  • Thanked: 1161 times
  • Alan, Peterborough, SA
Re: How to ID an ST1300 ABS
« Reply #6 on: December 22, 2014, 03:13:54 PM »
Hence ABS must be absolutely useless on a loose surface - correct?

Not completely useless......ABS just prevents wheel lock up but on a bike (at least with the ST) unless it's vertical straight line braking it won't make much difference. Depending on road surface etc. you may take longer or shorter to stop than a non-ABS equipped bike. Regardless you shouldn't rely on it and just maintain your usual braking method.

Where a lot of people get into trouble with is the CBS (combined) brakes which is standard on all 1300's so you no longer have independent front and rear braking.
1999 :bl11  2004 :13Candy

FarRider #921- BR15, BR17, CR1

 

Offline Biggles

  • "Top Dog" 10000 club
  • *****
  • Posts: 14121
  • Thanked: 2564 times
  • Bridgeman Downs, Brisbane
Re: How to ID an ST1300 ABS
« Reply #7 on: December 22, 2014, 03:48:23 PM »
Where a lot of people get into trouble with is the CBS (combined) brakes which is standard on all 1300's so you no longer have independent front and rear braking.

After 124,000 kays on ABS ST13s, I'm still waiting for the braking system to let me down.  It's a marvel in the wet.  I don't do enough gravel roads to know if it would help me there.
For the modern man who lives in the city, riding a bike might be one of the only ways to escape the humdrum monotony. To take off and ride. To be both at one with nature and one with the bike. To feel masculine. Adam Piggott

OzSTOC #16  STOC #6135  FarR #509  IBA #54927
 

Offline saaz

  • Supreme "2000" Club Member
  • *****
  • Posts: 4542
  • Thanked: 41 times
  • Canberra ACT
Re: How to ID an ST1300 ABS
« Reply #8 on: December 22, 2014, 03:59:00 PM »
ABS on the more modern bikes is fine in gravel, at least for a road bike. I have never come near having the ABS kick in on gravel roads, as you can brake pretty hard if you try, and the traction control for the rear wheel is hard to get kicking in (I know the ST1300 does not have traction control). I tend to try and not go near that limit in gravel and the wet through old fashioned restraint, but you can go a lot faster than you think. Combined braking also works fine, at least the Trophy system does, and I think even better than rear brake only.

On a dedicated dirt bike than having the ability to disable ABS and traction control can be a plus, but only for a rider that can use those extra limits to control the bike balancing the front and rear by controlled power. For most punters ABS is a far better bet in all conditions.
John
(Ridden on and forever in our hearts)
1996 Honda ST1100P
2014 Triumph Trophy SE
Ozstoc, STOC #7239, Farrider #461 Ulysses #061681, IBA #59143 and some others